FDOM40B-XXXSX: Product features, specifications and application scenarios

HANBit FDOM40B-XXXSX is an embedded SSD (DOM, Disk on Module) with industrial-grade IDE/PATA interface, suitable for various industrial control equipment, embedded systems and application scenarios with high reliability and stability requirements.

The following is a detailed introduction to HANBit FDOM40B-XXXSX:

FDOM40B-XXXSX Product Overview

HANBit FDOM40B-XXXSX is an embedded SSD series provided by HANBit Electronics. This hard drive is known for its high reliability, durability and wide temperature support, and is very suitable for harsh environments and industrial equipment that needs to run for a long time.

Naming Rules

• FDOM: The abbreviation of Flash Disk on Module, which means embedded flash memory module.
• 40B: Indicates the use of 40-pin standard IDE interface (PATA).
• XXX: Indicates storage capacity (such as 128MB, 512MB, 1GB, 8GB, etc.).
• SX: Identifies features, such as S for SLC flash memory, and X may indicate extended functions.

FDOM40B-XXXSX Features

Interface and Compatibility

• 40-pin IDE interface (PATA): compatible with various industrial motherboards and embedded system motherboards.
• Supports standard ATA protocol, compatible with old equipment and industrial automation equipment.

High reliability design

• SLC flash memory (single-layer storage unit): has extremely high write life and data reliability.
• Built-in ECC (Error Correction Code) technology to effectively prevent data errors.
• Supports Wear-Leveling (even wear technology) to extend storage life.

Wide temperature support

• Provide standard temperature and wide temperature versions:
• Standard temperature: 0°C to 70°C.
• Wide temperature: -40°C to 85°C, suitable for extreme environments.

Stable performance

• Read speed: up to 40MB/s.
• Write speed: up to 20MB/s.
• Low power design, suitable for fanless devices and low power applications.

Data Protection

• Supports power-off protection design to prevent data loss caused by accidental power failure.
• Durable mechanical design to withstand vibration and shock.

Specifications of FDOM40B-XXXSX

Parameter	Description
Interface type	40-pin IDE/PATA
Storage capacity	128MB to 8GB
Flash type	SLC (single-level cell)
Operating temperature range Standard temperature	0°C to 70°C; wide temperature: -40°C to 85°C
Voltage requirement	5V ± 10%
Data transfer speed	Read: up to 40MB/s; Write: up to 20MB/s
Durability	Write life up to 100,000 P/E cycles (SLC)
Dimensions	Standard 40-pin DOM form factor (approximately 50mm x 25mm)
Power consumption	Approximately 0.5W to 1W when working

HFDOM40B-xxxSx Physical Specifications Images

Application scenarios of FDOM40B-XXXSX

Industrial control and automation

PLC, CNC machine tools, industrial automation production lines, etc.

Embedded systems

Embedded motherboards, IoT gateway devices.

Medical equipment

Medical imaging equipment (such as ultrasound instruments), diagnostic equipment.

Old equipment upgrade

Provide modern storage solutions for traditional equipment, replacing mechanical hard disks.

Installation and compatibility of FDOM40B-XXXSX

Device support

Make sure the motherboard has a 40-pin IDE interface and supports the required storage capacity.
Can be directly plugged into the motherboard without additional power cables.

Installation location

Usually installed at the IDE interface of the motherboard, it takes up little space and is very suitable for compact devices.

Data protection

It is recommended to use the wide temperature version in industrial environments to ensure stable operation under high or low temperature conditions.

Selection and purchase recommendations of FDOM40B-XXXSX

Capacity selection

Choose capacity according to actual needs: 128MB, 512MB, 1GB, 8GB, etc.
Consider whether you need to store intensive data.

Temperature version

For general indoor environments, choose the standard temperature version.
The wide temperature version is suitable for scenes with high temperature, low temperature or drastic temperature fluctuations.

Recommended suppliers

Contact HANBit or industrial hardware suppliers (such as Mouser, Digi-Key, etc.) directly to purchase genuine products.

FAQs

How to determine whether my device is supported?

• Check the motherboard manual to confirm that the 40-pin IDE interface and the required storage capacity are supported.
• If the device supports the standard ATA protocol, it is compatible with the FDOM40B series in most cases.

How to avoid data loss caused by power failure?

• Use a version that supports power failure protection.
• In critical devices, it is recommended to back up data regularly.

SLC, MLC, and TLC?

• If you pursue high durability and reliability, choose SLC.
• MLC provides higher cost-effectiveness and is suitable for applications with lower performance requirements.

FDOM40B-XXXSX Datasheet

FDOM40B-XXXSX Datasheet PDF

Summary

HANBit FDOM40B-XXXSX is an embedded solid-state drive tailored for industrial applications. With its high reliability, wide temperature support, and IDE interface compatibility, it has been widely used in industrial automation, embedded systems and other fields. If you need a stable and reliable storage solution, the FDOM40B series is a trustworthy choice.

Statement:All articles (images, texts, audio) on this site are uploaded and shared by users, or integrated from relevant internet sources, only for user's learning. If your rights are violated, please contact the administrator to delete! Link to this article: https://www.jinftry.com